BLACK FRIDAY SALE!
10% OFF ON SELECTED PRODUCTS!
CODE: BOOSTED10

OFFER EXPIRES IN:

00
:
00
:
00
:
00
VAG 1.8T 20v Turbo BAM APY ECUMASTER EMU Black Engine Management Unit
Free UK shipping on all orders over £200.00
×
VAG 1.8T 20v Turbo BAM APY ECUMASTER EMU Black Engine Management Unit ECU With Plug and Play Adaptor
VAG 1.8T 20v Turbo BAM APY ECUMASTER EMU Black Engine Management Unit ECU With Plug and Play Adaptor
Click to zoom in

VAG 1.8T 20v Turbo BAM APY ECUMASTER EMU Black Engine Management Unit ECU With Plug and Play Adaptor

ECUMASTER
£1,270.40
The EMU Black  stand-alone engine management system is designed to operate the most advanced and complex engines available. It is a successor of our proven system, EMU. Throughout EMU’s lifetime we collected lots of data that allows us to substantially improve the device hardware and software. EMU Black targets race...
£1,270.40

VAG 1.8T 20v Turbo BAM APY ECUMASTER EMU Black Engine Management Unit ECU With Plug and Play Adaptor

The EMU Black  stand-alone engine management system is designed to operate the most advanced and complex engines available. It is a successor of our proven system, EMU. Throughout EMU’s lifetime we collected lots of data that allows us to substantially improve the device hardware and software.

EMU Black targets race cars, road cars, motorcycles, boats, and stationary engine applications.

The EMU Black controls fueling, ignition and auxiliary systems on 1-12 cylinder engines including those with drive-by-wire throttles (E Throttle) and VVT.

It can drive up to 6 passive or 12 smart coils directly and does not require external amplifier/power modules to achieve this. Sophisticated drive-by-wire strategies provide a wide range of throttle control along with advanced plausibility (fault/error) checking for safety.

Free, easy to install firmware upgrades further improve system capabilities (e.g. new strategies, trigger patterns, CAN data streams).

The EMU Black features more built-in value than any other aftermarket ECU. It easily matches the functionality of other stand-alone management systems with multiple inputs and outputs. Unlike many other ECU systems, the EMU Black has built-in wideband lambda input (Bosch LSU 4.2, and LSU 4.9 sensors wire directly in), MAP control connector (4 bar MAP sensor on board), 2 EGT probe inputs and an input to directly connect a Flex Fuel ethanol content sensor. All of this provides greater flexibility, reduces costs and negates the requirement for external or supplemental signal conditioning control systems and the associated wiring that other management systems require.

Whats Included!

Emu Black ECU

Adapter ( Interconnector) for VAG 1.8T 20V  BAM APY Engines

Tuning Cable

Added Extra: 

Bosch 4.9 Short Lambda Sensor + Connector +£110

TECHNOLOGY

The EMU Black is assembled according to IPC-S-815A standards to ensure high reliability of the product. The device is manufactured on an automated assembly line with optical inspection, automatically tested including burn-in. The PCB board quality and design, special surface coating and IP65 enclosure keeps the device operational in the harshest environments. The components used allow continued operation in a very wide temperature range (AECQ-100 GRADE 2 (-40 to +105˚C).

SPECIFICATION

GENERAL

Temperature range AECQ100 GRADE2 (-40 to +105˚C)
Reverse battery protection Yes, internal
Operating voltage 6-22V, immunity to transients according to ISO 7637
Enclosure IP 65, custom CNC machined aluminium
Size (mm) and weight(g) 150x72x31, 390
Connectors 1 x 24, 1 x 39 FCI Automotive connector
PC communication USB (with PC client software), serial, CAN

OUTPUTS

Injector outputs 6 protected outputs 5A, low side
Ignition outputs 6 outputs 7A(15A peak) (passive & active coils supported)
Aux outputs 6 protected outputs 5A, low side
Other outputs Full bridge up to 7A, can be used as separate outputs or 2 H-Bridges
WBO heater Protected low side up to 5A
Communication Serial, CAN BUS 2.0B

INPUTS

Analog inputs 9 inputs, resolution 10Bits, 0-5V (protected)
EGT inputs 2 for K-Type thermocouple
Knock sensor 2 inputs
Oxygen sensor LSU 4.2, LSU 4.9 or Narrow band
Trigger inputs 3 (primary, 2 cams) Hall/ VR software selectable
VSS 1 (Hall / VR)
Flex Fuel Sensor Yes
Switch inputs 3 inputs, switched to ground

SENSORS

Temperature sensors IAT, CLT, Oil temperature, AC evap temperature
Pressure sensor MAP, Oil pressure, Fuel pressure (user defined characteristic), AC pressure sensor, Back pressure
Oxygen sensor LSU 4.2 or 4.9 (built in controller), Narrow band, external WBO controllers
Speed Vehicle speed sensor (VR/HALL), Gear sensor (sensor, calculated)

FUELING

Injectors Up to 8 HiZ injectors (sequential)
Injection angle control 0-720 deg, start or end of injections
Battery compensation User defined, wizard for popular injectors
Fueling strategies VE based speed density, Alpha N
Air charge temp. Based on IAT and CLT
VE table 2 tables 16×20 (Load x RPM), resolution of 0.1%
Individual cylinder trim Yes
Staged injection Yes
Additional correction Oxygen sensor corrections, EGT correction (per cylinder), BARO, TPS vs MAP, TPS vs RPM, Warmup, Nitrous, LC, ALS, ASE, Fuel pressure, Knock sensor
Lambda based real time correction Using Lambda target table
Acc. / Deceleration enrichment Yes

IGNITION

Ignition outputs 6 for passive and active coils (software selectable)
Supported triggers N-1, N-2, N-3, N+1, Multitooth, Subaru triggers, Nissan trigger, Lotus Elise, Audi trigger, Renault Clio Wiliams / Alpine, Colt 1.5CZ, Wrangler
Ignition angle table 2 tables 16×20 (Load x RPM), resolution of 0.5 Deg
Per cylinder trim Yes
Dwell time battery compensation Used defined,  wizard for popular coils
Odd fire compatibility Application dependent
Additional correction CLT, IAT, TPS vs MAP, Nitrous,  Idle, Knock sensor, LC, Pit limiter, ALS, Flat shift, Timers, Acc. enrichment

KNOCK SENSING

Channels 2
Resonant frequency range 1-20kHz, 3rd order AAF
Sampling Ignition event driven, knock window
Actions Ignition retard, fuel enrichment, dashboard indication

IDLE CONTROL

Control type PWM solenoids (2,3 wires), drive by wire, stepper motors (bi and unipolar),  ignition cut, fuel cut
Control strategy Open / Close loop , ignition angle control
VE correction Yes, for Alpha-N
Corrections AC clutch, coolant fan, analog input

BOOST CONTROL

Boost ref  and target tables 2 sets 10×10 (TPS vs RPM)
Control strategies Open / Closed loop (PID based)
Corrections Gear, VSS, IAT, EGT

DRIVE BY WIRE

Control strategy Advanced 3D PID + static friction compensation
Supported throttles All with DC motor and current requirement lower than 6.5A

 

Wizard for 28 popular electronic throttles

PPS to throttle position characteristic 3D table
BLIP support Yes
ALS support Yes

TRACTION CONTROL

TC strategy Delta RPM, gear compensation
Torque reduction Spark cut using 3D table (16×20)
Sensitivity control 10 position rotary switch

VARIABLE VALVE TIMING

Supported systems VVTi, MiVec, VANOS, Double Vanos
Number of camshafts 2
Control strategy PID based closed loop, CAM angle target tables 12×12

FLEX FUEL

Ethanol content measurement Yes
Fuel temperature measurement Yes
Tables blending VE, IGN, Lambda/AFR, Boost, Cranking fuel, ASE, Warmup
Fuel temperature PW correction Yes

SPORT

ALS 2 independent ALS setting, DBW support
Shift light Per gear shift light
Launch control Yes
Gear cut Yes (Open loop), DBW blip supported

 

Source: Switch, load cell, CAN

Pit limiter Yes
Rolling anti lag Yes

ENGINE PROTECTION

Fail safe values for critical sensors Yes
Dashboard indication of failures Yes, user defined
Over temperature engine protection Yes (oil and coolant), user defined, RPM limit
Low oil pressure protection Yes, user defined, shut off
Fuel pressure protection Yes, fuel dose compensation, RPM limit, engine shut off
High exhaust temperature Alarm, per cylinder fuel trim, boost limit

CAN BUS

CAN standard 2.0B 125, 250, 500, 1000 kbps
Supported CAN Dashes ECUMASTER, Motec M800 Set 1, Haltech E8 E11v2, Pectel SQ 6, AEM
Supported OEM CAN streams BMW E46, Citroen C2, Mazda RX8, Ford ST, Polaris RZR, Mini Cooper R53, Fiat 500, Renault Clio, Lotus, Ford Fiesta, Ford ST, EVO X (AYC support)

OTHER

Unused injection outputs can be used as AUX output Yes
Output functions Fuel pump, coolant fan, parametric outputs, nitrous control, PWM 3D table output,  AC clutch, main relay, speedometer, tachometer
Password protection Yes, 2 levels
Timers Fuel, Ignition, Boost, timers controlled by virtual outputs
Serial dashboard support AIM, RaceTechnology
Autotune Yes
Built in trigger scope Yes
Logging Real time logging to PC computer, logging on external loggers (serial / CAN)
Read More
Read Less
Do we ship abroad ?

Yes we do, to almost anywhere in the world though remember the postage is often high when shipping anything bulky. Most bulky items we export will go by UPS so you can track the package online and could reach America within 48 hours providing its in stock !

However there are a few countries we do not ship to, some of these include: Israel, Thailand, Malaysia, Indonesia, Russia, Nigeria, Macedonia, Syria, Ukraine, Lebanon.

Why is postage on bulky items to some countries expensive compared to some other companies ?

LFor both yours and our safety we use well known couriers such as DPD Local and UPS for shipping, then we know exactly where it is in the world at any time and we know its going to arrive safely. Shipping small items can be cheap, but items such as bodykits are expensive to ship - we have a very small margin on the postage fees merely to cover packaging. We can now ship using standard post on some items, however using all methods you may incur import charges when you receive the goods for which we cant be responsible for.

BREXIT 2021 EUROPEAN TAXATION CHANGES:

For European Customers prices now displayed in cart once you enter your address will have 20% UK VAT Tax removed, however you will have to pay some form of Duties / VAT prior to delivery of your goods.

If you are unsure of charges we recommend you should contact your local authorities ahead of placing your order.

Availability:

Not everything on our website is in stock, if you need a part desperately please contact us first to confirm availability before placing your order.

How do I place an order if I live within the UK ?

You can either order here in our online shop or you can phone us or email us, using the following number/address are below.

Phone: 07985319479

Email: darkroadperformance@outlook.com

How do I place an order if I live outside the UK ?

Returns Procedure:

- Before returning any goods please read all our terms and conditions. - Dark Road Performance must be informed by e-mail or telephone on 0044 (0) 7985319479 of any items that you wish to return for credit or exchange within 7 working days commencing the day of delivery. A member of staff will provide you with a Returns Notice Number. - Please also ensure that you include a copy of your invoice when shipping any items back to us as well as your Returns Notice Number. - If an item is sent back to us without a Returns Notice Number; a refund will not be given. - No parts that have been used, fitted or installed will be accepted for Credit or Refund. - Any parts returned must be in resalable condition. - We will not under any circumstances pay any VAT/Import Duties on Returns, If we are requested to do so your return will be rejected/abandoned.

For orders that have been supplied correctly & assuming goods are in re-saleable condition: -Within 14 days from the day of delivery - Goods can be returned for ANY reason for a full refund of goods and initial delivery charge. -We do not cover returns postage back to us -After 14 days from the day of delivery - Goods can be returned but with a 20% handling charge. The initial delivery charge & return delivery charges will NOT be refunded. -After 28 days from the day of delivery – Goods are not accepted back for refund.

For orders that have been supplied incorrectly & assuming goods are in re-saleable condition: -Within 28 days from the day of delivery – Goods can be accepted back for full refund, refund for initial shipping and refund for return shipping. -If goods are not in re-saleable condition e.g fitted/test fitted, original packaging not present, covered in grease/lube etc, supplied correctly or incorrectly we will not accept for a refund.

At our discretion, we may drop ship your order direct from a UK supplier. If we arrange to drop ship an item it will be arranged internally, you only pay the price agreed in advance.

Yes it is.

Please make sure that you follow below steps:

1/ Download the package from themeforest.net (the file is in zip format)

2/ Extract the file you've just downloaded.

3/ Find this file: ella-3.0.0-sections-ready.zip in the folder Ella Sections Ready 3.0.0, then you just need to upload ella-3.0.0-sections-ready.zip file to your Shopify store.

To save your time and reach our support quickly, please follow below steps:

1/ Create a staff account for us (with Themes permission and Settings permission) http://docs.shopify.com/manual/settings/account/staff-members

2/ Capture screenshot or video for the issue you get.

3/ Specify which template and version you are using.

4/ Describe clearly how to reproduce the issue.

5/ Send all information (staff account, screenshot, video, template name and version, description of the issues, link) to support@halothemes.com

Yes, we will assist you to install the template if needed

Yes, we do. Please send your customisation requests to support@halothemes.com, we will give you our quote. Thank you.

Yes. You can turn on/off the animation in the Setting page.

Yes. You can turn on/off almost any blocks on the page (featured products, slideshow, banners, related products, recent products,...).

Yes, we have a setting for you to switch between these two options: Display on Hover and Display on Click.

The theme package includes theme source, Photoshop design files, sample data and manual guide.

That is not a problem. You just need to modify the width/height ratio in theme settings.

Your cart

×